Arduino Shield 40pcs×20cm female to female Dupont cables
- 40P color dupont line
- length:20cm
- 1p-1p female to female pin header
- a row including of 40 root
- Compatible with 2.54mm spacing pin headers
Package Contents:
- a row of 2.54mm 1P-1P dupont line X 2
Arduino Shield 40pcs×20cm male to female Dupont cables
- 40P color dupont line
- length:20cm
- 1p-1p male to female pin header
- a row including of 40 root
- Compatible with 2.54mm spacing pin headers
Package Contents:
- a row of 2.54mm 1P-1P dupont line X 2
Breadboard Power Supply Module 3.3V/5V For Arduino Board
Fuente de alimentación para conectar directamente en el Breadboard, compatible con circuitos de 5V y 3.3 V
- Apply to MB102 breadboard
- Input voltage: 6.5-12 V (DC) or USB power supply
- Output voltage: 3.3V/5V can switch over
- Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V
- On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.
Aviso: Sólo incluye la fuente de alimentación, el Breadboard no está incluido.
Character LCD Module Display 2004 204 20X4 For Arduino
The module is a low-power consumption character LCD Module with a built-in controller.
The module can be easily interfaced with a MCU.
Display Format: 20 Characters x 4 lines.
Supply voltage: 5V.
It is fantastic for Arduino based project.
- Fully assembled and tested Serial LCD 20×4 Module.
- White Text, Blue backlight.
- Analog Interface.
- Size:9.8cm x 6cm x 1.2cm – 3.86inch x 2.36inch x 0.47inch.
- Package Included:
- 1 x LCD display module
Digital Humidity & Temperature Sensor DHT1
Relative humidity and temperature measurement
All calibration, digital output, excellent long-time stability without additional components
Ultra-long signal transmission distance, ultra-low energy consumption
4-pin installation
Hall switch sensor module Motor speed test
On-board LM393 voltage comparator chip and hall sensing probe, support 5 V / 3.3 V voltage input.
On-board signal output, the output signal is effective instruction low level and at the same time, the output signal lights out can be directly and single-chip microcomputer IO connection.
Signal detection sensitivity can adjust.
Reserve all the way more circuits (P3 voltage drawn).
PCB board size: 30 (mm) x15 (mm)
HC-SR501 New Human Sensor Module Pyroelectric Infrared
- The automatic sensor: to enter the sensor output range is high, people leave the sensor range of the automatic delay off high, output low.
- The photosensitive control (optional, factory is not set) may set the photosensitive control during the day or light intensity without induction.
- The temperature compensation (optional, factory is not set): In the summer when the ambient temperature rises to 30 ~ 32 ℃, slightly shorter detection range, temperature compensation can be used as a performance compensation.
- Two trigger mode: (can be selected by jumpers)
- a, can not repeat the trigger: the sensor output high, the delay time is over, the output will automatically become low from high;
- b, repeatable trigger: the sensor output high after the delay period, if the human body in its sensing range activities, its output will remain high until after the delay will be left high to low (sensor module review Measured activities of each body will be automatically extended after a delay time, and the final event of the delay time Starting point of time).
- With induction blocking time (the default setting: 2.5S block time): sensor module, after each sensor output (high change Into a low level),you can set up a blockade followed by time period, in this time period the sensor does not accept any sensor signal. This feature can have a «sensor output time» and «blocking time» the interval between the work produced can be applied to detect the interval Products; also inhibit this function during load switching for a variety of interference. (This time can be set at zero seconds – Tens of seconds).
- The working voltage range: the default voltage DC4.5V-20V.
- Micro-power consumption: static current «50 microamps, especially for battery-powered automatic control products.
- The output high level signals: types of circuits can be easily and docking.
Instructions
- 1. Sensing module for about a minute after power initialization time, during the interval to the output module 0-3 times a minute in standby mode.
- 2. Should avoid direct lighting such as interference sources close the surface of the lens module so as to avoid the introduction of interference signal generator malfunction; use of the environment to avoid the flow of the wind, the wind sensor will also cause interference.
- 3. Sensor module using a dual probe, the probe’s window is rectangular, dual (A per B million) in the direction of the ends of long, when the body passed from left to right or right to left when the reach the dual IR time, distance difference, the greater the difference, more sensitive sensors, when the body from the front to the probe or from top to bottom or from bottom to top direction passing, dual IR not detected changes in the distance, no difference value, the sensor insensitive or does not work; so the sensors should be installed dual direction of the probe with human activities as much as possible parallel to the direction of maximum to ensure that the body has been passed by the dual sensor probe. To increase the sensing range of angles, the module using a circular lens, the probe also makes sense on all four sides, but still higher than the upper and lower left and right direction of sensing range, sensitivity and strong, still as far as possible by the above installation requirements.VCC, trig (control side), echo (receiving end), GND
Dimensions and Adjustment
Note: The potentiometer clockwise to adjust the distance, sensing range increases (about 7 meters), on the contrary, sensing range decreases (about 3 meters).Delay adjustment potentiometer clockwise rotation, sensor delay longer (about 300S), the other hand, induction by the short delay (about 5S).Applications
- Security Products
- The human body sensors toys
- The human body sensor lighting
- Industrial automation and control, etc.
Electrical parameters
- Product Type: HC–SR501 Body Sensor Module
- Operating voltage range: DC 4.5-20V
- Quiescent Current: <50uA
- Level output: High 3.3 V /Low 0V
- Trigger: L can not be repeated trigger/H can be repeated trigger(Default repeated trigger)
- Delay time: 5-200S(adjustable) the range is (0.xx second to tens of second)
- Block time: 2.5S(default)Can be made a range(0.xx to tens of seconds
- Board Dimensions: 32mm*24mm
- Angle Sensor: Operation Temp: -15-+70 degrees
- Lens size sensor: Diameter:23mm(Default)
Keypad 4×4 matrix keyboard buttons LED Shield
Un modúlo infaltable para nuestras prácticas con microcontroladores, este board tiene:
- Una matriz de 4 x 4 pulsadores.
- Una fila de 4 pulsadores con GND comun y resistencia de 1k a VCC
- Una fila de 8 diodos LED con VCC comun y una resistencia de carga de 1k.
Listo para utilizarlo con nuestros experimentos con Arduino y Raspberry PI
Content
1 pcs ofKeypad 4×4 matrix keyboard buttons LED Shield.
Laser Dot Diode Module Head WL Red mini 650nm 6mm 5V 5mW x 2
Laser Dot Diode Module Head WL Red
- Output Power: 5mW, Wavelength: 650nm
- Working Voltage: 5v, Operating Current: less than 40 mA
- Laser Shape: Dot
- Working temperature: -10º~40º
- housing: Copper
- Dimensions: 6.5 X 18 mm
Pack de 2 unidades.
LED RGB Clear Common Cathode x 5
How about an RGB LED? These 5mm units have four pins – Cathode is the longest pin. One for each color and a common cathode. Use this one LED for three status indicators or pulse width modulate all three and get mixed colors!
Features:
- Forward Voltage (RGB): (2.0, 3.2, 3.2)V
- Luminosity (RGB): (800, 4000, 900)mcd
1 Package 5 Pcs
light Sensor Module LM393 for Arduino DO/AO output W Cables 3.3-5V
This module adopts LM393 voltage comparator as the main chip. And it is perfect for light control applications. And onboard power indicator will be turned on when the module is powered by 3.3V – 5V voltage.
Working Voltage: DC 3.3V – 5V
- Sensitivity is adjustable.
- DO and AO outputs.
- PCB Size: 28mm*13mm
Package Contents: 1 x LM393 light Sensor Module
Male to Male Solderless Flexible Breadboard Jumper Cable Wires For Arduino, 65Pc
- 49 pcs 120mm length
- 8 pcs 150mm length
- 4 pcs 200mm length
- 4 pcs 240mm length
- total:65pcs(65pcs/lots)
Male to Male Solderless Flexible Breadboard Jumper Cable Wires For Arduino,65Pc
Package Contents:
- 65pcs
MQ-2 MQ2 Smoke Gas + Alcohol Detector Sensor
This Arduino Gas Sensor can detect smoke, methane, carbon dioxide and other gases.It is capable of detecting various gases.This arduino-compatible special sensor raise alarms when the smoke, methane or any other harmful gas leaks in its reach.
- Arduino smoke gas sensor
- Detects smoke, methane, carbon dioxide and other gases
- Gives alarms when the smoke/gas leaks
Type : MQ-2
(Used in homes and factories, gas leakage monitoring devices, suitable for the detection of liquefied petroleum gas, butane, propane, methane, alcohol, hydrogen gas, smoke, etc..)- Gas: smoke
- Detection range: 300 to 10000ppmm
- The characteristics gas: 1000ppmm, isobutane
- Sensitivity: R in air / Rin, typical gas ≥ 5
- Sensing Resistance: 1KΩ 50ppm toluene to 20KΩ in.
- Response time: ≤ 10s
- Recovery time: ≤ 30s
- Heat resistance: 31Ω ± 3Ω
- Heating current: ≤ 180mA
- Heating voltage: 5.0V ± 0.2V
- Heating power: ≤ 900mW
- Measuring voltage: ≤ 24V
- Working conditions of ambient temperature: -20 ℃ ~ +55 ℃
- Humidity: ≤ 95% RH
- Environmental oxygen content: 21%
- Storage conditions Temperature: -20 ° C to +70 ° C
- Humidity: ≤ 70% RH
Documents:
Manual técnico MQ-2Ejemplo de conexiones.
NRF24L01+Antenna Wireless Transceiver Module For Microcontrol
2 Unidades por pedido.
The real GFSK monolithic transceiver chip
- Built-in hardware and link layer
- Automatic response and automatic retransmission function
- Address and CRC check function
- Wireless rate: 1 or 2 MBPS
- SPI interface rate: 0 ~ 8MBPS
- 125 optional channels work
- Channel switching time is very short, can be used for frequency hopping
- Fully compatible with nRF24XX series
- I/O can accept 5v level of input
- ±60ppm 16MHz crystal
- Low working voltage: 1.9 ~ 3.6 V
- The global open ISM frequency band, the maximum 0dbm transmitted power, free license to use.
- Transmission distance up to 100 meters in outdoor open occasions!
Documentación
Alimentación principal 3.3V, pines de dat compatibles con 5v, se aconseja poner una resistencia de 120Ω en serie para SCK, MISO, CSN, CE.
Revise la documentación, librerías y ejemplos.
Pi Cobbler Breakout Kit for Raspberry Pi from Adafruit
Now that you’ve finally got your hands on a Raspberry Pi® , you’re probably itching to make some fun embedded computer projects with it. What you need is an add on prototyping Pi Cobbler from Adafruit, which can break out all those tasty power, GPIO, I2C and SPI pins from the 26 pin header onto a solderless breadboard. This mini kit will make «cobbling together» prototypes with the Pi super easy. Designed for Raspberry Pi Model B Revision 1.0.
This Cobbler is in a compact shape, which is the least bulky way to wire up. We also have the fancier T-Cobbler.
The Pi Cobbler mini kit comes with a 26 pin ribbon cable, a custom PCB, ribbon cable socket and header pins. A little soldering is required to put it together but its really easy, even a beginner can do it in 15 minutes so please click to read the tutorial Once soldered together, the cable plugs between the Pi computer and the Cobbler breakout. The Cobbler can plug into any solderless breadboard (or even a prototyping board like the PermaProto). The Cobbler PCB has all the pins labeled nicely so you can go forth and build circuits without keeping a pin-out printout at your desk. We think this will make it more fun to expand the Pi and build custom circuitry with it.
The Adafruit Pi Cobbler is compatible with both versions 1 and 2 of the Raspberry Pi Computer – for version 2 computers, note that the GPIO #21 has been replaced with GPIO #27 and that the I2C pins are now I2C port #1 instead of #0. All other pins are the same.
Please note, this kit only contains a 26 pin ribbon cable, a custom PCB, ribbon cable socket and header pins. A Raspberry Pi, breadboard, breadboarding wires, cables, components, case, power supply, etc is not included! We do stock many of those items in the shop, so check those out as well!
Power supply module with switch para Arduino Input: 6.5-12V Output: 5V AMS1117
Fuente de alimentación para Arduino y Tasperry PI, entrada 6.5V a 12V, salida 5V
- Onboard AMS1117-5.0 chip.
- On-board DC jack, input voltage range of 6.5V-12V.
- Board 7 * 7 self-locking switch, convenience to control power is turned on and off.
- Onboard power indicator to indicate power is turned on.
- Output voltage interface, connection to facilitate the experimental.
- Board size: 48.5 (mm) x12.5 (mm)
Relay Module 2-Channel 5V for Arduino
This is a 5V 2-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Microcontroller(Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
5V 1-Channel Relay interface board,It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on.
Product Features
- 5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current
- Equiped with high-current relay, AC250V 10A ; DC30V 10A
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
- Indication LED»»s for Relay output status
RF 433Mhz transmitter and receiver link kit for Arduino
Kit de emisor y receptor para radiocontrol y transmisión de datos, compatible con Arduino
Remote control switch, receiver module, motorcycles, automobile anti-theft products, household anti-theft products,electric doors, shutter doors, windows, remote control socket, remote control the LED, remote control stereo,remote control electric gate, garage door remote control, remote control retractable doors, remote control volumegate, pan doors, remote control door opener, door closing device control system, remote control curtains, alarm system, alarm, remote control motorcycle, remote control electric cars, remote control such as MP3.
Usarlo con Arduino:
Documentacón y ejemplos de servidor y cliente con la biblioteca Virtualwire de Arduino
Receiver module parameters
Product Model MX-05V Working voltage: DC5V quiescent current: 4MA Receiver Frequency: 433.92MHZ Receiver sensitivity:-105DB Size: 30 * 14 * 7mm external antenna: 32CM single wire, wound into a spiralEmission head technology parameters
Product Model: MX-FS-03V Transmission Distance :20-200 m (different voltage, different effects) Operating Voltage :3.5-12V Dimensions: 19* 19mm Ways of working: AM transfer rate: 4KB / S transmission power: 10mW Emission frequency: 433M External antenna: 25cm ordinary multi-core or single core line Pinout from left → right: (the DATA; the VCC; GND with)Remarks
- VCC voltage to be consistent with the module operating voltage, and power filtering to do;
- Antenna reception module is better to connect the 1/4 wavelength antenna, generally use 50 ohm single-core wire,the length of the antenna 433M is about 17cm;
- Reception antenna location on the module also affects the installation, the antenna as far as possible straight awayfrom the shield, high pressure, and interference source place; receiving frequency used, decoding and oscillation resistor should match with the launch.
Sensor DS18B20 Waterproof Digital Thermal Probe
The detector uses DS18B20 temperature sensor chip ,each pin of which is separated by heat shrinkable tube,to prevent short circuit and internal sealing glue,water proof and moisture proof.
- High quality stainless steel tube package,water proof,moisture proof and rust proof
- Each detector is single packaged after strict test.
- 3.0V ~ 5.5V power supply
- 9-12 bits adjustable resolution
- Temperature-detect range wide -55℃ ~ +125℃
- Need no external components,unique single-bus interface
Type : MQ-2
(Used in homes and factories, gas leakage monitoring devices, suitable for the detection of liquefied petroleum gas, butane, propane, methane, alcohol, hydrogen gas, smoke, etc..)- Gas: smoke
- Detection range: 300 to 10000ppmm
- The characteristics gas: 1000ppmm, isobutane
- Sensitivity: R in air / Rin, typical gas ≥ 5
- Sensing Resistance: 1KΩ 50ppm toluene to 20KΩ in.
- Response time: ≤ 10s
- Recovery time: ≤ 30s
- Heat resistance: 31Ω ± 3Ω
- Heating current: ≤ 180mA
- Heating voltage: 5.0V ± 0.2V
- Heating power: ≤ 900mW
- Measuring voltage: ≤ 24V
- Working conditions of ambient temperature: -20 ℃ ~ +55 ℃
- Humidity: ≤ 95% RH
- Environmental oxygen content: 21%
- Storage conditions Temperature: -20 ° C to +70 ° C
- Humidity: ≤ 70% RH
Documents:
Manual técnico MQ-2Ejemplo de conexiones.
Tact switch push button 6×6×H9(mm) x 10
Feature momentary contact, 4 pins, round black push button, through hole mounting, 6 x 6 x 9mm size, etc.
Used in the fields of electronic products, household appliances and more.
High precision mechanism design offers acute operation and long service life.
Bolsa de 10 unidades
Triple Axis Compass Magnetometer HMC5883L
This is the second revision of our popular HMC5883L Breakout Board. We’ve added a jumper to select pull-up resistors to make breadboarding more compact, and improved mounting flexibility by adding sturdier mounting holes. This board goes well with our 3 Axis Accelerometer to provide tilt compensated compass data.
If you are wanting to measure magnetic fields for any reason, be it getting a heading, or feeding into an inertial measurement unit, the HMC5883L breakout board will suit you nicely.
- Chips: HMC5883L
- Operating voltage: 3.3v -5v
- Output format: I2C
- dimension:16mm*18mm
Package Included: 1x HMC5883L Triple Axis Compass Magnetometer Sensor Module For Arduino/MWC/IMU
HMC5883L Compass Tutorial with Arduino Library
White Line Tracking TCRT5000 Black and Sensor Module
Model | I0526016 |
Quantity | 1 |
Color | Black |
Material | CCL |
Features | Tracking sensor module |
Application | for smart car, robot, etc. |
Other | Adopts TCRT5000 photoelectric sensor and comparator; Easy to use, good stability and anti-interference ability; Perfect for black & white line detection for smart car; Black line for low level output, white line for high level output; Operating Voltage: 5V |
Packing List | 1 x Tracking sensor module |