The Arduino Robot is the first official Arduino on wheels. The robot has two processors, one on each of its two boards. The  Motor Board controls the motors, and the Control Board reads sensors and decides how to operate. Each of the boards is a full Arduino board programmable using the Arduino IDE.

Both Motor and Control boards are microcontroller boards based on the ATmega32u4 (datasheet). The Robot has many of its pins mapped to on-board sensors and actuators.

Programming the robot is similar to the process with the Arduino Leonardo. Both processors have built-in USB communication, eliminating the need for a secondary processor. This allows the Robot to appear to a connected computer as a virtual (CDC) serial / COM port.

As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own robots. The Arduino Robot is the result of the collective effort from an international team looking at how science can be made fun to learn. Arduino is now on wheels, come ride with us!

Control Board Summary

Microcontroller ATmega32u4
Operating Voltage 5V
Input Voltage 5V through flat cable
Digital I/O Pins 5
PWM Channels 6
Analog Input Channels 4 (of the Digital I/O pins)
Analog Input Channels (multiplexed) 8
DC Current per I/O Pin 40 mA
Flash Memory 32 KB (ATmega32u4) of which 4 KB used by bootloader
SRAM 2.5 KB (ATmega32u4)
EEPROM (internal) 1 KB (ATmega32u4)
EEPROM (external) 512 Kbit (I2C)
Clock Speed 16 MHz
Keypad 5 keys
Knob potentiomenter attached to analog pin
Full color LCD over SPI communication
SD card reader for FAT16 formatted cards
Speaker 8 Ohm
Digital Compass provides deviation from the geographical north in degrees
I2C soldering ports 3
Prototyping areas 4

Motor Board Summary

  ATmega32u4
Operating Voltage 5V
Input Voltage 9V to battery charger
AA battery slot 4 alkaline or NiMh rechargeable batteries
Digital I/O Pins 4
PWM Channels 1
Analog Input Channles 4 (same as the Digital I/O pins)
DC Current per I/O Pin 40 mA
DC-DC converter generates 5V to power up the whole robot
Flash Memory 32 KB (ATmega32u4) of which 4 KB used by bootloader
SRAM 2.5 KB (ATmega32u4)
EEPROM 1 KB (ATmega32u4)
Clock Speed 16 MHz
Trimmer for movement calibration
IR line following sensors 5
I2C soldering ports 1
Prototyping areas 2

Schematic & Reference Design

EAGLE files for control and motor boards: arduino-robot-reference-design.zip

Power

The Arduino Robot can be powered via the USB connection or with 4 AA batteries. The power source is selected automatically.

The battery holder holds 4 rechargeable NiMh AA batteries.

NB : Do not use non-rechargeable batteries with the robot

For safety purposes, the motors are disabled when the robot is powered from the USB connection.

The robot has an on-board battery charger that requires 9V external power coming from an AC-to-DC adapter (wall-wart). The adapter can be connected by plugging a 2.1mm center-positive plug into the Motor Board's power jack. The charger will not operate if powered by USB.

The Control Board is powered by the power supply on the Motor Board.

Memory

The ATmega32u4 has 32 KB (with 4 KB used for the bootloader). It also has 2.5 KB of SRAM and 1 KB of EEPROM (which can be read and written with the EEPROM library).

The Control Board has an extra 512 Kbit EEPROM that can be accessed via I2C.

There is an external SD card reader attached to the GTFT screen that can be accessed by the Control Board's processor for additional storage.

Input and Output

The Robot comes with a series of pre-soldered connectors. There are a number of additional spots for you to install additional parts if needed.

All the connectors are labelled on the boards and mapped to named ports through the Robot library allowing access to standard Arduino functions. Each pin can provide or receive a maximum of 40mA at 5V.

Some pins have specialized functions :

  • Control Board TK0 to TK7: these pins are multiplexed to a single analog pin on theControl Board's microprocessor. They can be used as analog inputs for sensors like distance sensors, analog ultrasound sensors, or mechanical switches to detect collisions.
  • Control Board >TKD0 to TKD5: these are digital I/O pins directly connected to the processor, addressed using Robot.digitalRead() andRobot.digitalWrite) functions. Pins TKD0 to TKD3 can also be used as analog inputs with Robot.analogRead()
    Note: if you have one of the first generation robots, you will see that the TKD* pins are named TDK* on the Robot's silkscreen. TKD* is the proper name for them and is how we address them on the software.
  • Serial Communication: The boards communicate with each other using the processors' serial port. A 10-pin connector connects both boards carries the serial communication, as well as power and additional information like the battery's current charge.
  • Control Board SPI: SPI is used to control the GTFT and SD card. If you want to flash the processor using an external programmer, you need to disconnect the screen first.
  • Control Board LEDs: the Control Board has three on-board LEDs. One indicates the board is powered (PWR). The other two indicate communication over the USB port (LED1/RX and TX). LED1 is also accessible via software.
  • Both boards have I2C connectors available: 3 on the Control Board and 1 on the Motor Board.

Control Board Pin Mapping

ARDUINO LEONARDO ARDUINO ROBOT CONTROL ATMEGA 32U4 FUNCTION REGISTER
D0 RX PD2 RX RXD1/INT2
D1 TX PD3 TX TXD1/INT3
D2 SDA PD1 SDA SDA/INT1
D3# SCL PD0 PWM8/SCL OC0B/SCL/INT0
D4 MUX_IN A6 PD4   ADC8
D5# BUZZ PC6 ??? OC3A/#OC4A
D6# MUXA/TKD4 A7 PD7 FastPWM #OC4D/ADC10
D7 RST_LCD PE6   INT6/AIN0
D8 CARD_CS A8 PB4   ADC11/PCINT4
D9# LCD_CS A9 PB5 PWM16 OC1A/#OC4B/ADC12/PCINT5
D10# DC_LCD A10 PB6 PWM16 OC1B/0c4B/ADC13/PCINT6
D11# MUXB PB7 PWM8/16 0C0A/OC1C/#RTS/PCINT7
D12 MUXC/TKD5 A11 PD6   T1/#OC4D/ADC9
D13# MUXD PC7 PWM10 CLK0/OC4A
A0 KEY D18 PF7   ADC7
A1 TKD0 D19 PF6   ADC6
A2 TKD1 D20 PF5   ADC5
A3 TKD2 D21 PF4   ADC4
A4 TKD3 D22 PF1   ADC1
A5 POT D23 PF0   ADC0
MISO MISO D14 PB3   MISO,PCINT3
SCK SCK D15 PB1   SCK,PCINT1
MOSI MOSI D16 PB2   MOSI,PCINT2
SS RX_LED D17 PB0   RXLED,SS/PCINT0
TXLED TX_LED PD5    
HWB   PE2   HWB

Motor Board Pin Mapping

ARDUINO LEONARDO ARDUINO ROBOT CONTROL ATMEGA 32U4 FUNCTION REGISTER
D0 RX PD2 RX RXD1/INT2
D1 TX PD3 TX TXD1/INT3
D2 SDA PD1 SDA SDA/INT1
D3# SCL PD0 PWM8/SCL OC0B/SCL/INT0
D4 TK3 A6 PD4   ADC8
D5# INA2 PC6 ??? OC3A/#OC4A
D6# INA1 A7 PD7 FastPWM #OC4D/ADC10
D7 MUXA PE6   INT6/AIN0
D8 MUXB A8 PB4   ADC11/PCINT4
D9# INB2 A9 PB5 PWM16 OC1A/#OC4B/ADC12/PCINT5
D10# INB1 A10 PB6 PWM16 OC1B/0c4B/ADC13/PCINT6
D11# MUXC PB7 PWM8/16 0C0A/OC1C/#RTS/PCINT7
D12 TK4 A11 PD6   T1/#OC4D/ADC9
D13# MUXI PC7 PWM10 CLK0/OC4A
A0 TK1 D18 PF7   ADC7
A1 TK2 D19 PF6   ADC6
A2 MUX_IN D20 PF5   ADC5
A3 TRIM D21 PF4   ADC4
A4 SENSE_A D22 PF1   ADC1
A5 SENSE_B D23 PF0   ADC0
MISO MISO D14 PB3   MISO,PCINT3
SCK SCK D15 PB1   SCK,PCINT1
MOSI MOSI D16 PB2   MOSI,PCINT2
SS RX_LED D17 PB0   RXLED,SS/PCINT0
TXLED TX_LED PD5    
HWB   PE2   HWB

Communication

The Robot has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega32U4 provides UART TTL (5V) serial communication, which is available on digital the 10-pin board-to-board connector. The 32U4 also allows for serial (CDC) communication over USB and appears as a virtual com port to software on the computer. The chip also acts as a full speed USB 2.0 device, using standard USB COM drivers. On Windows, a .inf file is required. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Robot board. The RX (LED1) and TX LEDs on the board will flash when data is being transmitted via the USB connection to the computer (but not for serial communication between boards).

The ATmega32U4 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus; see the documentation for details. For SPI communication, use the SPI library.

Programming

The Robot can be programmed with the Arduino software (download). Select "Arduino Robot Control Board" or "Arduino Robot Motor Board" from the Tools > Board menu. For details, see the getting started page and tutorials.

The ATmega32U4 processors on the Arduino Robot come preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the AVR109 protocol.

You can bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header; see these instructions for details.

Automatic (Software) Reset and Bootloader Initiation

Rather than requiring a physical press of the reset button before an upload, the Robot is designed in a way that allows it to be reset by software running on a connected computer. The reset is triggered when the Robot's virtual (CDC) serial / COM port is opened at 1200 baud and then closed. When this happens, the processor will reset, breaking the USB connection to the computer (meaning that the virtual serial / COM port will disappear). After the processor resets, the bootloader starts, remaining active for about 8 seconds. The bootloader can also be initiated by double-pressing the reset button on the Robot. Note that when the board first powers up, it will jump straight to the user sketch, if present, rather than initiating the bootloader.

Because of the way the Robot handles reset it's best to let the Arduino software try to initiate the reset before uploading, especially if you are in the habit of pressing the reset button before uploading on other boards. If the software can't reset the board you can always start the bootloader by double-pressing the reset button on the board. A single press on the reset will restart the user sketch, a double press will initiate the bootloader.

USB Overcurrent Protection

Both of the Robot boards have a resettable polyfuse that protects your computer's USB ports from shorts and overcurrent. Although most computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.

Physical Characteristics

The Robot is 19cm in diameter. Including wheels, GTFT screen and other connectors it can be up to 10cm tall.

To Learn More

See also: getting started with the Arduino Robot and the Robot's library pages.

Arduino Robot

  • Brand: Arduino
  • Product Code:A001078
  • Availability:Producto agotado
  • S/.1,392.40

  • Ex Tax:S/.1,180.00

Ofertas

300K Pixel USB 2.0 Mini Webcam

300K Pixel USB 2.0 Mini Webcam

Plug and play web camera for your Pi. Displays have high resolution, providing true color images for..

S/.42.48 S/.81.66 Impuestos:S/.36.00

Arduino Ethernet Shield Rev3 WITHOUT PoE Module

Arduino Ethernet Shield Rev3 WITHOUT PoE Module

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is base..

S/.141.60 S/.212.40 Impuestos:S/.120.00

Kit Manejo de motores y servos, componentes de robot + Arduino UNO

Kit Manejo de motores y servos, componentes de robot + Arduino UNO

Este kit incluye un Arduino UNO y  los tres tipos de motores que se utilizan habitualmente en m..

S/.212.40 S/.335.12 Impuestos:S/.180.00

Arduino LilyPad USB - ATmega32U4

Arduino LilyPad USB - ATmega32U4

La placa LilyPad Arduino ha sido desarollada para las aplicaciones wearables y e-textiles (textiles ..

S/.94.40 S/.144.43 Impuestos:S/.80.00

Más Vendidos

Arduino Uno Rev3

Arduino Uno Rev3

The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital inp..

S/.113.28 Impuesto:S/.96.00

Male to Male Solderless Flexible Breadboard Jumper Cable Wires For Arduino, 65Pc

Male to Male Solderless Flexible Breadboard Jumper Cable Wires For Arduino, 65Pc

49 pcs 120mm length 8 pcs 150mm length 4 pcs 200mm length 4 pcs 240mm length total:65pcs(65p..

S/.25.96 Impuesto:S/.22.00

Ultrasonic Module HC-SR04 Distance Measuring Transducer Sensor

Ultrasonic Module HC-SR04 Distance Measuring Transducer Sensor

The HC-SR04 ultrasonic sensor uses sonar to determine distance to an object like bats or dolphins do..

S/.28.32 Impuesto:S/.24.00

Arduino Leonardo +headers

Arduino Leonardo +headers

Arduino Leonardo es una placa de prototipado electrónico que lleva un microprocesador integrado basa..

S/.118.00 Impuesto:S/.100.00

Ultimos Productos

Grove Starter Kit Plus

Grove Starter Kit Plus

Grove es una plataforma electrónica modular para el prototipado rápido. Cada módulo tiene una funció..

S/.354.00 Impuestos:S/.300.00

Official Raspberry Pi B+/2 Red & White Case

Official Raspberry Pi B+/2 Red & White Case

Finally! The Official Raspberry Pi Foundation's Raspberry Pi Case is now available! Specially m..

S/.70.80 Impuestos:S/.60.00

Weight Sensor (Load Cell) 0-10kg

Weight Sensor (Load Cell) 0-10kg

Applicable to electronic scale, price computering scale, electronic platform scale, digital scale; p..

S/.75.52 Impuestos:S/.64.00

Weight Sensor (Load Cell) 0-500g

Weight Sensor (Load Cell) 0-500g

Applicable to electronic scale, price computering scale, electronic platform scale, digital scale; p..

S/.111.30 Impuestos:S/.94.32

Camera Shield

Camera Shield

Camera Shield is the first shield board that support photograph, it is based on the solution of VC07..

S/.210.04 Impuestos:S/.178.00

DSO Touch

DSO Touch

DSO Touch, is a 2 channels digital pocket size oscilloscope. It is only 10mm thick with an aluminum ..

S/.472.00 S/.896.80 Impuestos:S/.400.00